These are the real foot bones of a 26-year-old man, built from a CT scan. Name all 26. Find the bone your whole leg rests on. Then measure the arch that holds you up.
This box is for questions 3 to 5 on your worksheet.
Finish these steps in the lab. Then this box opens.
The back half of the foot is made of 7 tarsals. The calcaneus is the heel bone. The talus sits on top of it, under the shin. In front are the navicular (boat-shaped), the cuboid (cube-shaped) and three cuneiforms (wedge-shaped).
The middle of the foot has 5 metatarsals. They are numbered 1 to 5, starting on the big-toe side. Metatarsal 1 is short and thick. Metatarsal 5 is on the little-toe side.
The toe bones are phalanges. Each small toe has 3: proximal (closest to the foot), middle, and distal (the tip). The big toe, the hallux, has only 2. So 3 + 3 + 3 + 3 + 2 = 14.
Your hand has 8 carpals, 5 metacarpals and 14 phalanges: 27 bones. Your foot has 7 + 5 + 14 = 26. Two feet hold 52 of your 206 bones. That is about 1 in every 4.
Most people also have two pea-sized sesamoid bones under the head of metatarsal 1. They grow inside a tendon. They are not counted in the 26. This CT model leaves them out, but a real X-ray shows them.
Now press "Real X-ray" on the photo and name the letters. Then answer questions 3 to 5.
This box is for questions 8 to 10 on your worksheet.
Finish these steps in the lab. Then this box opens.
A joint is a place where two bones meet. In this scan, bones at a joint sit 0 to 2 mm apart. In a living body, that gap is filled with smooth cartilage, so the bones slide instead of grinding.
The tibia and fibula grip the top of the talus, like a wrench around a bolt. Your table shows it: the only foot bone the tibia touches is the talus. The talus is the only foot bone the leg touches. So all of your weight passes through it.
Feel the two bumps on your ankle. The inside bump is the bottom end of the tibia (the medial malleolus). The outside bump is the bottom end of the fibula (the lateral malleolus). Press "Show the weight path" to see them.
From the talus, weight goes back and down into the calcaneus. It also goes forward through the navicular, the cuneiforms and the metatarsals toward the toes.
The calcaneus is 101.9 cm³, about 7 times the navicular. It is the first bone to hit the ground in each step. The Achilles tendon pulls up on its back end to lift your heel when you walk, run or jump. A big, strong bone fits that job. Structure fits function.
Now answer questions 8 to 10 on your worksheet.
This box is for questions 13 to 16 on your worksheet.
Finish these steps in the lab. Then this box opens.
Your heights went low, high, then low again: calcaneus 1.9 mm, talus 46.5, navicular 39.7, medial cuneiform 24.4, metatarsal 1 1.9 mm. That curve is an arch. This one runs along the inside of the foot. It is the medial longitudinal arch.
The outside of the foot has a lower arch. Its top bone, the cuboid, is only 15.3 mm up. A third arch runs across the foot, under the metatarsals.
An arch works like a stone bridge. It sends weight down to its two ends: the heel and the ball of the foot. Those are the bones that touched the floor. The arch also flattens a little with each step and springs back, like a spring.
Bones alone do not hold the arch. Ligaments tie the bones together. A tough band under the sole, the plantar fascia, ties the heel to the toes like the string on a bow. Muscles help too. This model has bones only.
In a flat foot (pes planus), the arch sinks. The navicular drops toward the floor, and the footprint fills in. In a high arch (pes cavus), the arch is tall. The footprint can break into two pieces.
Now press "Footprints" on the photo and judge the prints. Then answer questions 13 to 16.
Follow-along slideshow · opens with the phenomenon, teaches each part with Learn It slides, and walks through the worksheet, question by question
Printable student worksheet (PDF) · two pages, 16 questions
Low-write worksheet (PDF) · same questions with tick boxes, word banks and worked examples
Teacher guide: NYSSLS, SEP and CCC alignment (PDF)
What you will learn. I can locate and name the bones of the foot. I can explain how the shape of the foot's bones fits their job of holding up the body.
What is real: the bones are the right foot of a 26-year-old man, from a CT scan in the Virtual Skeleton Database (case 024), with the bottom 14 cm of his tibia and fibula. Every length, volume, gap and height on this page is measured from those scanned bones. The X-ray is a real normal right foot, seen from above. The footprints are real inked prints. What is changed or left out: the CT was taken lying down, with the foot pointed and rolled in, so the bones were turned to stand on a floor. The floor is where the bones would rest; a real foot also has skin and fat pads under it. The model has no cartilage, ligaments, muscles or sesamoid bones. It is one man's foot; other feet differ.
Bone models: Virtual Skeleton Database (SMIR), lower-extremity CT segmentations via BoneHub, CC BY-NC-SA 4.0; rendered by Ryan Sajdak. X-ray: Mikael Häggström, M.D., CC0 (turned a quarter turn). Footprints: Juan Carlos Fonseca Mata, CC BY-SA 4.0.
© 2026 Ryan Sajdak. This lab, its worksheets and its slides are free to use, share and change under the Creative Commons BY-NC-SA 4.0 license: give credit, do not sell it, and share your version the same way.